تاثیر دمای تغییر شکل روی ریزدانه کردن (تصفیه دانه) فریت در فولاد میکروآلیاژ Nb Ti با درصد کربن پایین
Influence of deformation temperature on the ferrite grain refinement in a low carbon Nb–Ti microalloyed steel
مقدمه
فرآیند های ترمومکانیکی کنترل شده TMCP برای فولاد میکروآلیاژ Nb Ti چندین بار با تولید صفحات و ورق های فولادی برای بهینه کردن خواص مکانیکی انجام شده است. ویژگی اصلی فولاد هایی که تحت فرآیند ترمومکانیکی قرار گرفته اند فوق ریز دانه بودن محصول نهایی آن ها می باشد. بنابراین، فولاد های با ساختار فریت فوق ریز دانه به میزان زیادی نظر مهندسین و محققین را جذب کرده است. زیرا در این مواد استحکام و چقرمگی با هم افزایش می یابند. تقاضا برای فولاد هایی که هر دو این خاصیت را توأم با هم دارند و همچنین جوش پذیری بالایی دارند، باعث شد که فولاد های کم کربن میکروآلیاژ به وجود بیایند.
برای رسیدن به ریزساختار فریت فوق ریزدانه چندین روش TMCP وجود دارد. نورد کنترل شده، یکی از روش های ارزان تولید فولاد استحکام بالا با استحکام تسلیمی در حدود ۶۰۰ مگاپاسکال می باشد[۱]. در فرآیند های تجاری نورد در اندازه دانه فریت یک محدودیت در حدود ۵ میکرون را دارد. گروه های زیادی گزارش کرده اند که به اندازه دانه زیر ۵ میکرون در فریت با فرآیند نورد کنترل شده با استفاده از روش های آزمایشگاهی TMCP برای فولاد های ساده کربنی و فولاد های کم کربن میکروآلیاژ دست یافته اند
جهت دانلود ترجمه تخصصی و فارسی این مقاله می توانید وجه آنرا پرداخت نموده و بلافاصله دریافت نمایید.
INTRODUCTION
The thermomechanical controlled processing (TMCP) of microalloyed steels has been employed for some times in the production of plates and sheet material in order to optimize mechanical properties. The central feature of thermomechanicallyprocessedsteelistheultrafinegrainsizeinthefinalproduct. Therefore, the ferrite grain refinement of structural steels has attracted considerable interest from engineering scientists due to its unique role of increasing both strength and toughness. Demand for steels possessing good combination of these properties, and weldability has led to the development of low carbon microalloyed steels.
There are several TMCP routs to obtain the fine ferrite grain microstructure. Controlled rolling is one of the most important operations for producing low-cost, high strength steels with yield strength as high as 600MPa [1]. A limiting ferrite grain size of around 5m appears to exist using commercial controlled rolling. In recent years, several groups have reported achieving ferrite grain size below the nominal 5m limit of controlled rolling steels, using laboratory scale TMCP methods for low carbon microalloyed and plain carbon steels.
محصولات مرتبط
بهبود فولاد میکروآلیاژی HSLA با وانادیم و تیتانیم
Effect of vanadium and titanium modification on the microstructure and mechanical properties of a microalloyed HSLA steel بهبود فولاد میکروآلیاژی HSLA…
اثر ترکیب روی بافت کریستالوگرافی آلیاژهای آلومینیوم
بافت کریستالوگرافی آلیاژهای آلومینیوم Effect of composition on crystallographic texture in hot-rolled Al-Li-Cu alloys اثر ترکیب روی بافت کریستالوگرافی در…
انجماد جهت دار سوپرآلیاژهای پایه نیکل
Effect of solidification rate on competitive grain growth in directional solidification of a nickel-base superalloy انجماد جهت دار سوپرآلیاژهای پایه…
اثر اندازه نمونه بر ریزساختار و انجماد جهت دار فاز بین فلزی Al2Cu
Effect of sample size on intermetallic Al2Cu microstructure and orientation evolution during directional solidification اثر اندازه نمونه بر ریزساختار فاز…
47,400 تومان قیمت اصلی 47,400 تومان بود.14,200 تومانقیمت فعلی 14,200 تومان است.
تنها اشخاصی که این محصول را خریداری کرده اند و وارد سایت شده اند می توانند در مورد این محصول بازبینی ارسال کنند.