تاثیر جنس انواع الکترودهای سیمی مختلف بر نرخ برشکاری فولاد D3
Effect of Various Wire Electrodes’ Material on Cutting Rate of D3 Material
چکیده
ماشینکاری تخلیه ی الکتریکی سیمی (WEDM) به طور وسیعی در ماشینکاری دقیق مواد هادی (رسانا) مورد استفاده قرار می گیرد. در این مطالعه، تاثیر مواد الکترودی مختلف بر کارکرد فرایند نظیر نرخ برشکاری (براده برداری) و زمان برشکاری مورد بررسی قرار گرفته است. آزمایشات تحت پارامترهای ثابت برشکاری TON، TOFF، IP، WP، WF، WT و SV انجام شدند. بر اساس میزان استفاده ی سیم های مختلف در فرایند WEDM، سه نوع سیم مختلف در آزمایشات مورد استفاده قرار گرفتند.
این سیم ها شامل سیم های برنجی، مسی با پوشش روی و مغز فولادی با روکش داخلی مس و خارجی روی بودند. قطر این سیم ها برابر ۰/۲۵ mm بوده و آزمایشات بر روی قطعه کار D3 با ضخامت ۲۰ mm انجام گرفته و نتایج حاصل (پارامترهای سرعت و زمان برشکاری) با یکدیگر مقایسه شدند. با توجه به نتایج تحقیق مشخص گردید که سرعت برشکاری فولاد D3 با استفاده از الکترود با مغز فولادی و روکش های Cu و Zn در مقایسه با سیم های برنجی و مسی با روکش روی بیشتر است.
جهت دانلود ترجمه تخصصی و فارسی این مقاله می توانید وجه آنرا پرداخت نموده و بلافاصله دریافت نمایید.
ABSTRACT
Wire electrical discharge machining (WEDM) is extensively used in machining of conductive materials when precision is of prime importance. In this study, the effect of the different electrode materials on performance characteristics i.e. cutting rate and cutting time were investigated. The experiments were conducted under the constant cutting parameters of TON, TOFF, IP, WP, WF, WT, SV. For the experiment, three wires are chosen on the basis of their maximum usage as a wire electrode in WEDM.
These three wires are Brass wire, zinc coated copper wire and Steel wire coated with primary coating of Copper and secondary coating of Zinc. These wires of 0.25mm diameter are operated on the D3 work piece material having thickness of 20mm and results are compared in the present investigation. The performance parameters which are compared in this study are cutting speed and cutting time. During the experimentation, it has been found that the cutting speed is maximum in case of Steel wire coated with Cu and Zn as compared to brass and zinc coated copper wire.
محصولات مرتبط
اثر میکروساختار ماده بر فرسایش ابزار هنگام ماشینکاری آلیاژهای سخت تیتانیوم
ماشین کاری آلیاژ تیتانیوم Experimental investigation on the effect of the material microstructure on tool wear when machining hard titanium alloys:…
استفاده از فولاد زنگ نزن آستنیتی AISI 316 به عنوان تقویتکننده در بتن
Practical and Economic Aspects of Application of Austenitic Stainless Steel, AISI 316, as Reinforcement in Concrete جنبههای عملی و اقتصادی…
آلومینات ها Aluminates
Aluminates آلومینات ها ABSTRACT Aluminates form in binary systems with alkali, alkaline earth or rare-earth oxides and share the high…
اثر کار مکانیکی بر ساختار آلیاژ منگنز آلومینیوم Effect Of Prior Working On The Structure Of Mn-29.5% Al-0.5% C ALLOY
Effect Of Prior Working On The Structure and Deformation Capacity Of Mn-29.5% Al-0.5% C ALLOY اثر کار مکانیکی اولیه بر ساختار…
تنها اشخاصی که این محصول را خریداری کرده اند و وارد سایت شده اند می توانند در مورد این محصول بازبینی ارسال کنند.