مشخصات آستنیت باقیمانده در فولاد آلیاژی پرکربن – پرکروم کوئنچ شده
Characteristics of Retained Austenite in Quenched High C-High Cr Alloy Steels
چکیده
در این مقاله مورفولوژی مارتنزیت و آستنیت باقیمانده فولاد آلیاژی پرکربن ۱.۵ mass%C-12 mass%Cr و ۱ mass%C-8 mass%Cr به وسیله میکروسکوپ نوری، XRD، SEM/EBSD و TEM مورد مشاهده قرار گرفت. مقدار آستنیت باقیمانده به صورت کمی بررسی و با روش های مشاهده XRD، EBSD و TEM مقایسه گردید. آستنیت باقیمانده به شکل بلوکی و فیلمی در ساختارهای مارتنزیتی توزیع شده بود. برای فولاد ۱.۵ mass%C-12 mass%Cr، مقدار آستنیت باقیمانده نوع بلوکی و نوع فیلمی در سه منطقه ی متمایز کاربیدی: کاربید اولیه، کاربید ثانویه و بدون کاربید، تقریباً برابر هستند. در مورد فولاد ۱ mass%C-8 mass%Cr، در رابطه با آستنیت باقیمانده نوع فیلمی تفاوت های خیلی زیادی میان این مناطق وجود ندارد. با این حال، آستنیت های باقیمانده نوع بلوکی با مقدار زیاد، به خصوص در منطقه اطراف کاربید اولیه توزیع شده اند.
جهت دانلود ترجمه تخصصی و فارسی این مقاله می توانید وجه آنرا پرداخت نموده و بلافاصله دریافت نمایید.
ABSTRACT
In this paper, the morphologies of martensite and retained austenite for 1.5mass%C-12mass%Cr and 1mass%C-8mass%Cr steels were observed by means of optical microscopy, XRD, SEM/EBSD and TEM. The amount of retained austenites was quantitatively investigated and compared with XRD, EBSD and TEM observation methods. The retained austenites were distributed in the form of a block type and a film type in the martensite structures. For the 1.5mass%C-12mass%Cr steel, the amount of block type retained austenite and film type one are almost equal in three distinct regions of carbide; primary carbide, secondary carbide and without carbide. In the case of 1mass%C-8mass%Cr steel, as to film type retained austenite there are not so much differences among those regions. However, block type retained austenites are distributed with much amount, especially in the region around primary carbide
محصولات مرتبط
اثر نیتروژن روی خواص خزشی فولاد زنگ نزن
Evaluation of the effect of nitrogen on creep properties of ۳۱۶LN stainless steel from impression creep tests ارزیابی اثر نیتروژن روی…
انجماد جهتدار آلیاژهای آلومینیوم – مس Directional solidification of aluminium–copper alloys
Directional solidification of aluminium–copper alloys انجماد جهتدار آلیاژهای آلومینیوم-مس ABSTRACT Directional solidification experiments have been carried out on different Al–Cu…
انتخاب پوشش Coating Selection
Coating Selection انتخاب پوشش ABSTRACT An improved approach to coating selection should thus allow progressive elimination and lend itself to a…
اتصال نفوذی مس به فولاد زنگ نزن تحت فشار ناگهانی
Impulse pressuring diffusion bonding of a copper alloy to a stainless steel with/without a pure nickel interlayer اتصال نفوذی مس به فولاد…
تنها اشخاصی که این محصول را خریداری کرده اند و وارد سایت شده اند می توانند در مورد این محصول بازبینی ارسال کنند.