آنالیز خواص مکانیکی و سطوح شکست چدن داکتیل دوفازی آستمپر شده
Analysis of mechanical properties and its associated fracture surfaces in dual-phase austempered ductile iron
چکیده
این تحقیق به ارزیابی سطوح شکست نمونه های کششی مربوط به نسل جدیدی از چدن داکتیل دوفازی آستمپر شده (ADI) که متشکل از آسفریت (میکروساختار متداول ADI) و فریت آزاد (دگر شکل) می باشد، پرداخته است. مشخصات سطح شکست کششی و رفتار کششی هشت میکروساختار دوفازی ADI در چدن داکتیل آلیاژی (با مقادیر مختلف فریت و آسفریت)، مورد بررسی قرار گرفتند. علاوه بر این، نمونه هایی با زمینه کاملا فریتی یا کاملا آسفریتی (ADI) به عنوان نمونه شاهد تولید شدند. با افزایش مقدار آسفریت، استحکام کششی، تنش تسلیم، و سختی میکروساختار دوفازی ADI نیز بیشتر می شوند.
ترکیب مطلوبی از استحکام و افزایش طول تا شکست در نمونه ها به دست آمد. مکانیزم شکست DI تحت اعمال بار استاتیکی تک محوری در دمای اتاق، جوانه زنی، رشد و به هم پیوستن میکروحفرات است. سطح شکست DI فریتی، توپوگرافی نامنظم متشکل از دیمپل ها و حفرات کروی (ناشی از تغییرشکل زیاد) را نشان می دهد (مشخصات شکست نرم). میکروساختار حاوی مقادیر جزئی آسفریت (کم تر از ۲۰%) نسبت به میکروساختار کاملا فریتی، رفتار مکانیکی بهتری از خود نشان داده است. در این میکروساختارها مناطقی با شکست کلیواژ در آخرین منطقه منجمد شده وجود دارد که ناشی از وجود آسفریت در این مناطق است.
با افزایش مقدار آسفریت، مقدار تغییرشکل حفرات کروی کاهش یافته و توپوگرافی سطح شکست هموارتر می گردد که ناشی از وجود حجم بالایی از مناطق کلیواژ می باشد. با استفاده از سیکل حرارتی خاصی، میکروساختارهایی با زمینه پرلیتی حاوی شبکه پیوسته ای از فریت آلوترومورفیک (در مرز دانه های آستنیت تبلور مجدد یافته) به دست آمدند. نتایج آزمون های مکانیکی نشان داد که در نتیجه ایجاد زمینه پرلیتی، خواص مکانیکی بهبود قابل توجهی یافته است. در توپوگرافی سطح، حفرات کروی تغییرشکل نیافته (یا با تغییرشکل جزئی) و سطح همواری دیده شدند که ناشی از وجود مقادیر بالای پرلیت می باشند. هم چنین، الگوی دیمپلی مربوط به مناطق فریتی نیز مشاهده گردید.
جهت دانلود ترجمه تخصصی و فارسی این مقاله می توانید وجه آنرا پرداخت نموده و بلافاصله دریافت نمایید.
ABSTRACT
This work aims at evaluating the fracture surfaces of tensile samples taken from a new kind of ductile iron referred to as ‘dual-phase Austempered Ductile Iron (ADI)’, a material composed of ausferrite (regular ADI microstructure) and free (or allotriomorphic) ferrite. The tensile fracture surface characteristics and tensile properties of eight dual-phase ADI microstructures, containing different relative quantities of ferrite and ausferrite, were studied in an alloyed ductile cast iron. Additionally, samples with fully ferritic and fully ausferritic (ADI) matrices were produced to be used as reference. Ferritic–pearlitic ductile irons (DI) were evaluated as well.
For dual-phase ADI microstructures, when the amount of ausferrite increases, tensile strength, yield stress and hardness do so too. Interesting combinations of strength and elongation until failure were found. The mechanisms of fracture that characterise DI under static uniaxial loading at room temperature are nucleation, growth and coalescence of microvoids. The fracture surface of fully ferritic DI exhibited an irregular topography with dimples and large deformation of the nodular cavities, characteristic of ductile fracture. Microstructures with small percentages of ausferrite (less than 20%) yielded better mechanical properties in relation to fully ferritic matrices.
These microstructures presented regions of quasi-cleavage fracture around last-to-freeze zones, related to the presence of ausferrite in those areas. As the amount of ausferrite increased, a decrease in nodular cavities deformation and a flatter fracture surface topography were noticed, which were ascribed to a higher amount of quasi-cleavage zones. By means of a special thermal cycle, microstructures with pearlitic matrices containing a continuous and well-defined net of allotriomorphic ferrite, located at the grain boundaries of recrystallised austenite, were obtained. The results of the mechanical tests leading to these microstructures revealed a significant enhancement of mechanical properties with respect to completely pearlitic matrices. The topographies of the fracture surfaces revealed a flat aspect and slightly or undeformed nodular cavities, as a result of high amount of pearlite. Still isolated dimple patterns associated to ferritic regions were observed.
محصولات مرتبط
اثر ترکیب روی بافت کریستالوگرافی آلیاژهای آلومینیوم
بافت کریستالوگرافی آلیاژهای آلومینیوم Effect of composition on crystallographic texture in hot-rolled Al-Li-Cu alloys اثر ترکیب روی بافت کریستالوگرافی در…
بیومواد آلومینای چقرمه شده با زیرکونیا برای جایگزین مفصل
Advances in zirconia toughened alumina biomaterials for total joint replacement پیشرفت ها در بیومواد آلومینای چقرمه شده با زیرکونیا برای…
اثر افزودن کاربید تیتانیوم روی خواص ترموالکتریک سرامیک ها
Effect of titanium carbide addition on the thermoelectric properties of B4C ceramics اثر افزودن کاربید تیتانیوم روی خواص ترموالکتریک سرامیک…
اطلس عیوب ریخته گری
اطلس عیوب ریخته گری عیوب ریخته گری از گذشته در قطعات باعث بحران بوده اند و مهم ترین وظیفه ریخته گران…
تنها اشخاصی که این محصول را خریداری کرده اند و وارد سایت شده اند می توانند در مورد این محصول بازبینی ارسال کنند.