تنش پسماند در جوشکاری GTAW
Influence of welding speed and power on residual stress
during gas tungsten arc welding (GTAW) of thin sections
with constant heat input: A study using numerical
simulation and experimental validation
اثر سرعت جوشکاری و توان بر تنش پسماند در جوشکاری GTAW مقاطع نازک با ورودی گرمای ثابت
مطالعه ای با استفاده از شبیه سازی و اعتبارسنجی تجربی
ABSTRACT
The temperature distribution and residual stresses for a GTAW circumferential butt joint of AISI 304 stainless steel using numerical simulation have been evaluated. For evaluation of weld induced residual stresses, the analysis of heat source fitting was carried out with heat inputs ranging from 200 to 500 J/mm to arrive at optimal heat input for obtaining proper weld penetration and heat affected zone (HAZ). For this chosen heat input, the influence of different weld speeds and powers on the temperature distribution and the residual stresses is studied. The heat source analysis revealed the best choice of heat input as 300 J/mm. The residual stresses on the inner and outer surfaces, and along the radial direction were computed. Increase in temperature distribution as well as longitudinal and circumferential residual stresses was observed with the increase in weld speed and power. The validity of the results obtained from numerical simulation is demonstrated with full scale shop floor welding experiments.
جهت دانلود رایگان نسخه لاتین این مقاله اینجا کلیک کنید .
چکیده
توزیع دما و تنش های پسماند برای یک اتصال سربه سری محیطی GTAW فولاد ضدزنگ AISI 304 با استفاده از شبیه سازی عددی، ارزیابی شده است. ارزیابی تنش های پسماند ناشی از جوش، تحلیل برازانش (fitting) منبع گرما در ورودی های گرما متغیر از J/mm 200 تا ۵۰۰ برای رسیدن به ورودی بهینه گرما در دستیابی به نفوذ مناسب جوش و ناحیه متاثر از گرما (HAZ) با ویژگی های مطلوب، انجام شد. برای این ورودی گرمای منتخب، اثر سرعت های مختلف جوش و توان های مختلف بر توزیع دما و تنش های پسماند مطالعه می شود. تحلیل منبع گرما نشان داد که بهترین انتخاب برای ورودی گرما، J/mm 300 است. تنش های پسماند روی سطوح داخلی و خارجی و در راستای جهت شعاعی، محاسبه شدند. افزایش توزیع دما بعلاوه تنش های پسماند طولی و محیطی، با افزایش سرعت جوش و توان مشاهده شد. اعتبار نتایج بدست آمده از شبیه سازی عددی با آزمایش های جوش کاری کارگاهی تمام عیار نشان داده شد.
جهت دانلود ترجمه تخصصی و فارسی این مقاله می توانید وجه آنرا پرداخت نموده و بلافاصله دریافت نمایید.
محصولات مرتبط
مرکاپتوبنزیمیدازول بعنوان بازدارنده ی خوردگی مس در محیط کلریدی
: Mercaptobenzimidazole as a copper corrosion inhibitor Long-term immersion, 3D-profilometry, and electrochemistry مرکاپتوبنزیمیدازول بعنوان بازدارنده ی خوردگی مس در محیط…
اتصال نفوذی مس به فولاد زنگ نزن تحت فشار ناگهانی
Impulse pressuring diffusion bonding of a copper alloy to a stainless steel with/without a pure nickel interlayer اتصال نفوذی مس به فولاد…
سنتز پودر ZrB2 بوسیله احیا حرارتی بور ZrB2 Powders Synthesis by Borothermal Reduction
ZrB2 Powders Synthesis by Borothermal Reduction سنتز پودر ZrB2بوسیله احیا حرارتی بور ABSTRACT High-purity zirconium diboride (ZrB2) powders with submicrometer…
آماده سازی ذرات آلومینای ریزدانه مشتق شده از ژیپسیت بایر Preparation of Fine Alumina Powder
Preparation of Fine Alumina Powder آماده سازی ذرات آلومینای ریزدانه مشتق شده از ژیپسیت بایر ABSTRACT This study involves the…
تنها اشخاصی که این محصول را خریداری کرده اند و وارد سایت شده اند می توانند در مورد این محصول بازبینی ارسال کنند.